All Rights Reserved. Powered by TechWyse. Check the zones which have been indicated for issues, and correct any issues you may see. If you are unsure, please contact our monitoring station. The keypads feature a telephone style digital keypad and a Liquid Crystal Display LCD that shows the nature and location of all occurrences. Keypad display back lighting is programmable to always stay on or to light only when a key is pressed, then turn off a few minutes later.
The keypads also feature a built-in sounder that will sound during alarms and troubles. These sounds can be optionally suppressed in some of your keypads so as not to disturb other users of the system. Ask your installer if this has been done. Alpha keypads feature a 2-line, character alphanumeric LCD that can display system messages in user-friendly English.
These keypads can also be programmed with custom zone descriptors. NOTE : There may be multiple keypads on your system. One, the primary keypad, will continue to operate under faulted conditions.
When using the keypad to enter codes and commands, sequential key depressions must be made within 3 seconds of one another. If 3 seconds elapse without a key depression, the entry is aborted and must be repeated from its beginning. Displays protection point identification and system status, messages, and user instructions. Late arrivals can enter through an entry delay zone without causing an alarm if the system is disarmed before the entry delay time expires.
Allows automatic bypassing of certain areas, which allows movement within your house without causing an alarm. An alarm will occur immediately upon opening any protection point, including entry delay zones.
Displays previously bypassed protection zones. An alarm will occur immediately upon opening any perimeter protection point, including entry delay zones. CHIME mode. When on, any entry through a protected delay or perimeter zone while the system is disarmed will cause a tone to sound at the Keypad s. This key is also used to display all zone descriptors that have been programmed for your system, by holding the key down for at least 5 seconds. KEYS Used to enter your individual security access code s.
Refer to the Panic Keys section for descriptions of these functions. Your system has installer-programmed time delays, known as exit delay and entry delay. Whenever you arm your system, exit delay gives you time to leave through the designated exit door without setting off an alarm.
Exit delay begins immediately after entering any arming command, and applies to all modes of arming protection. If programmed, a slow beeping will sound throughout the exit delay period. Entry Delay gives you time to disarm the system when you reenter through the designated entrance door.
But the system must be disarmed before the entry delay period ends, or an alarm will occur. The keypad will beep during the entry delay period, reminding you to disarm the system. These modes provide greater security while on the premises or while away for extended periods of time. See your installer for your delay times. At the time of installation, you were assigned an authority level and a personal four-digit security code, known only to you and yours.
The security code must be entered when arming and disarming the system. The authority level defines the system functions that you can perform.
As an additional safety feature, other users that do not have a need to know your code can be assigned different security codes, and each user can be given a different authority level. Users are identified by "user numbers", which are assigned when assigning a user's security code. All codes can be used interchangeably when performing system functions within the limits of each code's authority level a system armed with one user's code can be disarmed by another user's code , with the exception of the Operator Level C code.
See Authority Levels paragraph on the following page for details regarding authority levels. This feature is intended for use if you are forced to disarm or arm the system under threat.
When used, the system will act normally, but can silently notify the central station of your situation, if that service has been provided. The duress code is pre-assigned by the installer during installation authority level 6.
Note: If "Quick Arming" was programmed by the installer, the [ ] key can be pressed in place of the security code when arming the system.
The security code must always be used to disarm the system, however. Authority levels define the system functions a particular user can perform. Depending on the authority assigned to you, there are certain system functions you may be prohibited from performing. In summary, there are six authority levels, each having certain system restrictions as shown below.
Level 1 Master: Can perform all system functions in assigned partitions, and can add, delete or change Manager and Operator level users. The Installer adds master codes. Level 2 Manager : Can perform system functions in assigned partitions, and can add, delete or change Operator level users. Level 3 Operator A : Can perform system functions in assigned partitions, but cannot add or delete other users.
Level 5 Operator C : Can arm the system in assigned partitions, but cannot disarm the system unless the system was armed with this code. Level 6 Duress : Can arm and disarm the system, but also sends a silent panic alarm to the central station, if that service is connected. The keypad will display the partition s that you are authorized to operate, and your user number and authority level in each partition. To change a user's authority level, that user must first be deleted, and then added again.
Single digit user numbers must be preceded by a "00" example, , , etc. Security codes are entered as 4-digit numbers. NOTE: When adding, changing or deleting users, all other alpha keypads in that partition will display "User Edit Mode — Please Stand By", and key depressions except Panic at those keypads will be ignored.
Panic key depressions will cause an alarm and terminate user entry. You can exit any of the user edit modes described on the following pages at any time by doing the following:. Press either or , or don't press any key for 10 seconds. Enter the new user's 3-digit User Number Enter 4-digit security code for that user. What does check long range radio mean? Consult the control panel instructions to determine the valid zone numbers for that control panel.
Enter programming with your installer code followed by Compass software is useful for programming honeywell alarm control panels through a computer. If you can get into programming as tom described above you should be able to reset the master code by following this procedure:. Tolle Fotos und beeindruckende Grafiken einfach und. Missed the Crypto Boat? Now is the time to get in. How to get into graduate school without letters of.
If you have a grade point average of 3. How To Establish A. Pin on Software Interface Screenshot. Pin by Best Hacks on howtohacksfacebook Hack facebook. Find out what GMAT score you need to get into your dream. Your email address will not be published.
0コメント