Anti-corrosion connectors Built-in amplifier compensates insertion loss Sensitive meter for in-line use; pocket size and light weight With electronic buzzer. Easy operation, attenuation, audio tone and back light Powered by the receiver, nice tool for campers.
PS: work great with directv hd swim signal; it uses 2X1. Browse and discover shows, movies and sports. Tap to tune in to any show on your TV from your Kindle Fire.
Set your DVR to record your favorite shows from anywhere. Track your favorite teams and get real-time scores and schedules. You can for example display it right next to your TV or hide it behind The Wall Mount is not covering any airflow No drilling is required depending on your type of wall Friends started requesting the wall mount Do doubts keep creeping into your mind?
Potential sources can include buying guides for Direct Tv Satellite Dish Setup , rating websites, word-of-mouth testimonials, online forums, and product reviews. Take at least two readings with a level, on the upper mast, that are 90 degrees apart from one another.
Loosen both skew bolts and set the skew by rotating the dish mounting bracket to align the mark with the required angle on the skew scale which you wrote above. Tighten the skew bolts securely. See Table 1 for the required torque values. After the skew is set, do not try to finetune the skew angle when aiming the dish. Grounding, other devices, and in-home cabling must also meet these requirements.
RG-6 coaxial cable rated for at least to MHz must be used in this installation. Do not use existing cables such as RG as it may cause signal loss. Also, be sure that any outdoor connections are made using waterproof F-connectors rated for MHz or greater. The cable length between the DISH Damage caused by over-tightening is not covered by the limited warranty.
Tighten all indoor coaxial cable connections to the receiver only by hand. If you use a wrench, you may over-tighten the connections and damage your equipment. Connect a temporary cable to a peaking meter. Thread the other end of the cable through the LNBF arm and bracket. Attach the LNBFs to the bracket using the included screws. Do not adjust the skew. Ensure you are peaking the dish using transponder 11 or higher. With the peaking meter still connected, tighten the mast clamp and elevation bolts using the torque values listed in Table 1 on page 6.
Re-confirm signal strength after tightening the bolts. Remove the temporary cable used for peaking the dish. Thread the cable s from the receiver s through the LNBF arm and bracket.
Connect a cable from DPP Then, place a washer and nut on the end of each bolt, tightening it with your wrench. If they feel shaky, carefully separate them and tighten the bolts. One last component, the LNB, controls the dish's functionality. First, slide the handle of the LNB onto the open end of the arm. Secure it with nuts and bolts, then take the LNB out of the box.
It looks almost like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place. You may need to loosen the LNB later to readjust it and improve the signal quality. Connect the adjustment panel on the dish to the wall mount.
Fit the dish onto the open end of the support. If everything is attached correctly, it will fit inside or behind the adjustment panel. You can then add the 1 or 2 remaining bolts to fasten these pieces together. If the dish looks good, then you're ready to position it to communicate with a satellite.
If the mount is meant to attach to the back of the panel, your satellite will also come with a pair of clips. Position them behind the support, then add the screws through them to bind the parts together. Part 3. Select a satellite you wish to connect to.
Pick a satellite that is in range of your particular dish. There are numerous satellites out there, but dishes cannot get signals from all of them. If you bought your dish from a TV service, for instance, you might have a hard time connecting to their competitor's satellites. Tracking sites list the names, which usually include the owning company or the service they provide. If you bought a satellite service, it is possible to receive satellite signals outside that service.
Since you usually need to replace several parts, it's easier to get a new satellite instead. Try to pick a satellite close to your area. If you subscribe to a particular TV service, you will need to use the company's satellites. The biggest providers have multiple satellites. Find the satellite's location before positioning the dish.
You're going to need to point the dish in the correct direction, then angle it up at the sky. This isn't easy to do if you don't know the satellite's positioning. Fortunately, satellites don't move much, so you can use a positioning database to adjust your dish.
The site will give you the precise positioning needed for your dish to receive the signal. You won't be able to receive a signal from a distant satellite. Don't expect to reach a Chinese satellite if you're in North America, for instance. Use the azimuth number to rotate the satellite. Have a compass handy and locate true north first. Then, look at the azimuth number and find where that is on the compass. North is considered 0 degrees, east is 90 degrees, south is degrees, and west is degrees.
Rotate the satellite dish horizontally until it points in the correct direction. Then, turn the satellite southwest from there.
Move the dish vertically to adjust its elevation. Once you know the height needed to reach the satellite, go behind the dish. Examine the end of the mount where it connects to the dish. You will see a bolt inside a slot labeled by degrees, usually 10 to Loosen the bolt by twisting it counterclockwise, then reposition the dish to the proper elevation.
Moving the bolt along the slot raises or lowers the dish. For instance, if the dish requires a degree elevation, it will point up into the sky almost as much as it possibly can. Slide the loosened bolt back toward the degree marker.
Adjust the dish's polarization until you get a clear signal. The final part that needs to be adjusted is LNB, responsible for receiving and sending the signal into your home. It is usually an arm on the front that points toward the dish. Test out the signal quality by hooking the dish up to the receiver and a TV, then loosen the connecting nut on the arm by turning it counterclockwise with a wrench. If the TV is far away, have someone else stand near it and give you feedback. You may need to wait to adjust the LNB until you're done with the wiring.
Take care of it before then, if you're able, so you don't have to keep climbing on the roof to make adjustments. The LNB can sometimes be controlled by turning a mount part on the back of the dish left or right. Part 4. Check your home first for a previously-used cable opening. The dish's cable needs its own little space to enter your home and hook up to your TV.
Unless your home is in the process of being built, drilling a single hole is the easiest way to do this. Position your TV and the satellite receiver nearby to prepare for the connection. It needs to be below the frost line, the lowest point that freezes in winter, which is about 3 in 7. Run a coaxial cable from the LNB to the receiver. Make sure the receiver is positioned close to the satellite to ensure the cable can reach it. TV service providers will also give you one when you buy a satellite from them.
The coaxial cable sometimes connects to the back of the satellite. Usually, though, it plugs directly into the LNB. Once the cord is in place, your TV will be able to receive the satellite signal. Turn on the TV to see if it works. The receiver may plug directly into the TV instead. Consult a wiring guide for specific instructions on how to connect the satellite, receiver, and your TV. If you bought the satellite from a TV service provider, they would also provide a wiring guide.
Turn on the TV to test the signal. Press the satellite button if your remote has one or navigate to the settings menu. You should be able to get a picture right away.
If the signal quality is poor, make sure you positioned the satellite dish correctly.
0コメント